Skip to content
Main -> Hook -> How To Setup Your Table Saw Out of The Box
  • 08.09.2019
  • by Gotilar
  • 0 comments

How To Setup Your Table Saw Out of The Box

Setting Up Your Stacked Dado Set

Look no further, your answers are right here. My Out-of-the-box Setup Guide will show you exactly what you need to do to set up your saw correctly. The emphasis is on safety and attention to detail. You want to set your saw up in such a way that you find success with your projects more easily. However, there are a few requirements for a safe workstation. The first and foremost being space. And obviously, you need to be able to navigate around the saw yourself.

If you need help with buying one, this guide should help. Although by doing this the results will most likely prove inaccurate and you might be endangering yourself in the process.

Quick and Easy DIY Dust Collection - Dust Deputy

Most new table saws will come fitted with a blade. And most guides will tell you that aligning the blade to the mitre slot should be the first thing to do. This is really down your own personal preference and the saw you are buying.

If you want to double check, then a saw aligning jig would be a fantastic purchase. The first thing we would recommend doing is making sure the blade is square to the table. This is done by raising the blade to it highest height and the tilt to 90 degrees. If not, you should find in your manual a way of adjusting this to get it right. If you are planning on doing bevel or compound cuts, it would also be wise to check the blade at 45 degrees. This can be easily done with a mitre square.

A general rule of thumb is that it should be no more than 8mm away from the blade along its curvature. If you need to make any adjustments to this it can be done easily by removing the kerf plate.

Most pencils are no more than 8mm thick so if you can fit them between riving knife and blade, the distance is too far. A table saw is mostly about ripping, so getting the rip fence set up correctly is almost as important as getting the blade correct.

There are a couple of things that you will need to do with the fence before it is right. A great way to do this is by using the sub fence in a vertical position and placing it up against the blade and checking by eye down the table. Depending on the size of the saw this can be a two or three man job. One thing to remember when fitting it is to make sure the sliding table sits very slightly above the main table. This is to prevent it dragging on the main table when pushing the wood through.

You want to set your saw up in such a way that you find success with your projects more easily. However, there are a few requirements for a safe workstation.

The first and foremost being space. And obviously, you need to be able to navigate around the saw yourself.

Saw hook up

Please, do not set your table saw up in a cramped area. Furthermore, keep the area organized and clean.

These are vital aspects of table saw safety. If you have a committed workshop, it is smart to place each of your big tools in a way that makes it easier on you. Keeping the entire space in mind can really save steps and increase efficiency.

Consider your workflow.

How to align your table saw miter gauge, blade and fence. These easy checks will help you make perfectly accurate cuts with your table saw. More than any other piece of woodworking equipment the careful set-up of the table saw will pay off with impressive results. Take your time do it right.

Lastly, if your workspace is on your own property, has an attached storefront, or is anywhere else that puts you in danger of interruption, you must make sure those nearby know not to interrupt you when they hear the saw running. Something as harmless as an opening door can lead to major consequences.

True Your Table Saw Miter Gauge, Blade and Fence

All it takes is the slightest slip and you are less one finger. Now that you have decided where your saw is going to go, time to pull it out and give it a good once over. Once you have the saw out of the box, the first thing you should do is find the manual and read through it. Of course, make sure you have everything the manual says you are supposed to.

So your new table saw just delivered to your house! You're pumped. But how do you set this thing up the right way? Look no further, your answers are right here. The new table saw has arrived! Before you get going, it's recommended you get the saw setup correctly. Unsure how? This insight should help. Table Saw Set-up Guide / Multipurpose Gauge: A table saw blade must be perfectly parallel to the miter slots of your table saw top, or it will go through wood at.

Remember, when you buy online, do so from a reputable site like Amazon. That way you have peace of mind, knowing a multi-billion dollar company has your back. Most of the time, your saw is not going to be aligned properly fresh out of the box.

How To Set Up Your Table Saw

But before you go through the standard alignment processyou should check one specific aspect. Measure to make sure both miter slots are parallel with each other. If misaligned, you have a manufacturing mistake that cannot be fixed.

It will make your life more difficult and can create dangerous situations. Send it back and get a new one.

I needed to build a saw hook to make proper use a new Veritas crosscutting saw. The smaller pieces of maple were surfaced with the LV #4 low angle up. Trap normally is located directly in line with the cutting path of the saw blade. For ripping, you hook up small hose from saw-blade guard to t trap. It's not. Jobsite table saws are assembled the same way you'd set up a traditional cabinet saw or larger workshop table saw, but some of the parts.

Mikalkis

0 thoughts on “How To Setup Your Table Saw Out of The Box

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top